Ham Radio Practice Test
Practise for the Ham Radio with 915 exam-style questions, an explanation for every answer and stats that show what to study next.
Ham radio practice test: which exam are you taking?
There are three US amateur radio license exams: Technician (35 questions), General (35 questions) and Amateur Extra (50 questions). They are given by volunteer examiners under FCC rules in 47 CFR Part 97, and you need about 74 percent to pass each one. This free ham radio practice test has 20 newly written questions: 12 at Technician level, 5 at General and 3 at Extra, each with an explanation for every answer.
These are practice items, not real exam questions. The real exams take their questions word for word from public pools written by the NCVEC Question Pool Committee, so these are new questions on the same topics, not copies from the pools.
Everyone starts with Technician. According to ARRL, it gives you every amateur band above 30 MHz plus some limited HF privileges. General adds some privileges on every band, and Extra gives you all US amateur privileges.
Who can take a ham radio license exam?
Anyone who qualifies by examination can hold a US amateur license, except a representative of a foreign government (47 CFR 97.5). The rule sets no age or citizenship requirement. The classes build on each other: General requires a Technician pass as well, and Extra requires all three elements (97.501).
Under 97.509, a team of at least 3 accredited volunteer examiners (VEs) runs each exam, at a session coordinated by a Volunteer Examiner Coordinator (VEC). ARRL says sessions are held both online and in person. There is no Morse code test. The current rules in 97.501 list only Elements 2, 3 and 4.
Exam format and passing score
The FCC sets exam length and pass marks in 47 CFR 97.503. Pool dates are from ARRL's question pool page, checked November 12, 2026.
| License | Element | Questions | Correct to pass | Current pool valid |
|---|---|---|---|---|
| Technician | 2 | 35 | 26 (74.3%) | July 1, 2026 to June 30, 2030 |
| General | 3 | 35 | 26 (74.3%) | July 1, 2023 to June 30, 2027 |
| Amateur Extra | 4 | 50 | 37 (74%) | July 1, 2024 to June 30, 2028 |
We found no time limit in the federal rules, so ask your VE team how long the session allows.
Which question pool is current in 2026?
The Technician pool changed on July 1, 2026. ARRL says the new 2026 to 2030 pool has 409 questions. Compared with the old pool, 27 questions are new, 30 were removed and about 155 were modified. If your book or app says 2022 to 2026, it was written for a pool that ended June 30, 2026.
The General pool runs until June 30, 2027. A new General pool should follow, so check your General study material again then. The Extra pool runs to June 30, 2028. Questions withdrawn after release are listed on ARRL's withdrawn questions page.
What each exam covers
Each exam takes one question from every group in the pool's syllabus. So the number of groups in a subelement tells you how many questions you will see from it. The counts below come from copies of the three NCVEC pool syllabi, and they add up to the 97.503 totals.
| Topic | Technician (of 35) | General (of 35) | Extra (of 50) |
|---|---|---|---|
| FCC rules | T1: 6 | G1: 5 | E1: 6 |
| Operating procedures | T2: 3 | G2: 5 | E2: 5 |
| Radio wave propagation | T3: 3 | G3: 3 | E3: 3 |
| Amateur radio practices | T4: 2 | G4: 5 | E4: 5 |
| Electrical principles | T5: 4 | G5: 3 | E5: 4 |
| Components | T6: 4 | G6: 2 | E6: 6 |
| Practical circuits | T7: 4 | G7: 3 | E7: 8 |
| Signals and emissions | T8: 4 | G8: 3 | E8: 4 |
| Antennas and feed lines | T9: 2 | G9: 4 | E9: 8 |
| Safety | T0: 3 | G0: 2 | E0: 1 |
The exams change character as you move up. Technician is broad and practical: rules, repeaters, Ohm's law and safe station setup. General leans toward HF operating, with 15 of 35 questions on rules, operating procedures and station practices. Extra is mostly an electronics exam. Of its 50 questions, 30 cover electrical principles, components, circuits, signals and antennas.
How to split your study time
Split your time in roughly the proportions in the table, then adjust for what you already know.
- Technician: spend about a sixth of your time on FCC rules (6 of 35). The four technical areas, T5 to T8, deserve nearly half (16 of 35), and they share the same math: Ohm's law, power, decibels and wavelength. Safety, propagation and operating are 3 questions each.
- General: rules, operating and station practices are 5 questions each. Antennas and feed lines are 4, so practice SWR and dipole behavior.
- Extra: circuits (E7) and antennas (E9) make up 16 of 50 questions between them. Safety is a single question, so review it once and move on.
You can miss 9 questions on Technician or General, or 13 on Extra, and still pass. That margin covers a few hard calculations you skip, but not a whole subelement. Practice with fresh questions and work each calculation through instead of memorizing answer letters.
VirtuePrep's practice bank has 915 ham radio questions. Related pages: journeyman electrician and FE exam for more circuit theory practice, or browse all exams.
What does the exam cost, and what should you bring?
You pay twice: once for the exam session and once for the license. The session fee is set by the VEC, not the FCC. ARRL says the fee is usually $15 or less, and ARRL VEC charges $5 for candidates under 18. Other VECs may charge differently, so confirm with your session.
The FCC charges $35 for a new license under 47 CFR 1.1102. You pay it directly to the FCC after your application is filed, not to the exam team. For new license candidates under 18 who test with ARRL VEC, ARRL reimburses that $35 once the license is issued.
Before the session, register in the FCC's CORES system to get an FCC Registration Number (FRN). ARRL's checklist also asks you to bring a photo ID (or two non-photo IDs), the fee and any earlier exam credit certificate. You can use a calculator only if its memory is cleared, and you cannot use a phone or tablet as one.
After you pass
The VE team grades the exam and gives you a Certificate of Successful Completion of Examination (CSCE). It credits the elements you passed for 365 days (97.505), which matters if you plan to come back for the next class. A license normally runs 10 years (97.25), and you renew it with the FCC. If it expires, you have a 2-year grace period to renew, but you cannot transmit until you do (97.21).
20 free Ham Radio practice questions
Answer each one yourself, then open the answer. No account needed. These are study questions, not real exam questions.
-
You give your call sign at 7:00 p.m. as you start a simplex chat with a friend, and the two of you sign off at 7:25 p.m. What is the fewest number of additional times you must transmit your call sign during this contact?
- One, at the end of the contact
- Two, near 7:15 and at the end
- Three, by 7:10, by 7:20 and at the end
- None, since you gave it at the start
Show answer
Answer: C. FCC rules require you to give your call sign at least every 10 minutes during a communication and again at the end. After the 7:00 ID, you must identify by 7:10 and by 7:20, then once more when you finish at 7:25. That makes three more transmissions of your call sign.
-
Dana holds a General class license and Lee holds a Technician license. With Dana's permission, Lee wants to use Dana's station while she is out to make voice contacts on 14.250 MHz. Which statement is correct?
- Yes, because the station is licensed to a General class operator
- No, because Lee's own Technician privileges set the limit
- Yes, as long as Lee identifies with Dana's call sign
- No, because only the station's licensee may ever operate it
Show answer
Answer: B. What counts is the control operator's license class, not the station owner's. With Dana away, Lee is the control operator, and Technician privileges do not include the 20 meter band. Another licensed amateur may operate Dana's station, but only within his own privileges, and using Dana's call sign does not change that.
-
A 2 meter repeater in your area is listed with an output of 146.940 MHz and a standard negative offset. What frequency should your radio transmit on to access it?
- 146.340 MHz
- 146.940 MHz
- 147.540 MHz
- 145.940 MHz
Show answer
Answer: A. A standard 2 meter offset is 600 kHz, and a negative offset puts the repeater input below the output. 146.940 minus 0.600 is 146.340 MHz. The ARRL band plan pairs the 146.61 to 146.97 MHz output segment with the 146.01 to 146.37 MHz input segment, which is 600 kHz lower. 145.940 MHz would be a 1 MHz shift, which is not the 2 meter standard.
Source: ARRL band plan
-
You are setting up a handheld radio on 445 MHz. About what is the wavelength of that signal in free space?
- About 6.7 centimeters
- About 67 centimeters
- About 1.5 meters
- About 6.7 meters
Show answer
Answer: B. Wavelength is the speed of light divided by frequency. With light at about 300,000,000 meters per second, 300 divided by 445 MHz gives about 0.67 meters, or 67 centimeters. The shortcut to remember: wavelength in meters is 300 divided by frequency in MHz.
-
Your mobile transceiver draws 20 amperes on transmit. The power cable from the car battery to the radio has a total resistance of 0.04 ohm, counting both leads. About how much voltage is lost in the cable while you transmit?
- 0.08 volt
- 0.8 volt
- 5 volts
- 8 volts
Show answer
Answer: B. By Ohm's law, the voltage drop is current times resistance: 20 A times 0.04 ohm equals 0.8 V. On a 13.8 V system, losing that much can hurt transmit performance. That is why mobile radios are usually wired with short, heavy cable run directly to the battery.
-
A resistor in an indicator lamp circuit has 9 volts across it and 15 milliamperes flowing through it. What is its resistance?
- 135 ohms
- 1,670 ohms
- 600 ohms
- 60 ohms
Show answer
Answer: C. Resistance equals voltage divided by current. Convert 15 mA to 0.015 A, then divide: 9 V divided by 0.015 A equals 600 ohms.
-
Your 13.8 volt DC power supply is delivering 18 amperes to a transceiver. About how much power is the supply providing?
- About 32 watts
- About 1.3 watts
- About 3,400 watts
- About 248 watts
Show answer
Answer: D. Power is voltage times current: 13.8 V times 18 A is 248.4 W, or about 248 watts. Adding the two numbers, or dividing one by the other, does not give you power.
Source: OpenStax University Physics Volume 2, 9.5 Electrical energy and power
-
You want a 12 volt radio to run normally but draw essentially no current if someone hooks the battery leads up backward. Which single component placed in series with the positive lead does this?
- A diode
- A capacitor
- An inductor
- A resistor
Show answer
Answer: A. A diode lets current flow in one direction and blocks it in the other. In series with the positive lead, it conducts with correct polarity and blocks current when the leads are reversed. A series capacitor would block DC all the time, and an inductor or resistor passes DC in either direction. The diode does drop a little voltage, usually under a volt, in normal use.
Source: OpenStax University Physics Volume 3, 9.7 Semiconductor devices
-
Last week your SWR meter read 1.3 to 1 on your 2 meter antenna. After a storm it reads extremely high and nearby stations cannot hear you. Which is the most likely cause?
- The squelch control on the radio is set too high
- The transmitter power has been turned down
- An open or short in the feed line or antenna
- A slight change in antenna length from cold weather
Show answer
Answer: C. SWR rises when the load does not match the line. An open or short at the end of the line reflects nearly all the power, which drives SWR very high. Squelch affects only receive audio, SWR is a ratio that does not depend on power level, and a tiny length change would shift SWR only slightly.
-
You are listening to an amateur satellite's 435 MHz downlink as it passes overhead and begins moving away from you. Which way must you retune to keep the signal centered?
- Lower in frequency
- Higher in frequency
- No retuning, because Doppler shift does not affect FM
- To the opposite sideband
Show answer
Answer: A. This is the Doppler effect. When a source moves away from you, the frequency you receive drops, so you tune lower. On the way in, while the satellite approaches, the signal arrives above its nominal frequency. Doppler shift affects every radio signal, whatever the mode.
Source: OpenStax University Physics Volume 3, 5.7 Doppler effect for light
-
You are cutting wire for a half-wave dipole for 146 MHz. Before trimming for best SWR, about how long should the whole antenna be?
- About 0.5 meter
- About 2 meters
- About 4 meters
- About 1 meter
Show answer
Answer: D. A full wavelength at 146 MHz is about 300 divided by 146, or 2.05 meters, so half a wavelength is about 1.03 meters (roughly 40 inches). A working dipole usually ends up a few percent shorter than that, so start a little long and trim.
-
Two antennas, one on 146 MHz and one on 14 MHz, run the same power at the same distance from your neighbor's yard. Under FCC exposure limits for the general public, which one faces the stricter power density limit?
- The 14 MHz antenna, since the limit gets tighter as frequency drops below 30 MHz
- The 146 MHz antenna, since the 30 to 300 MHz range has the lowest limit
- Neither, since one limit applies across all amateur frequencies
- Neither, since amateur stations are exempt from the exposure limits
Show answer
Answer: B. From 30 to 300 MHz, the FCC general population limit is 0.2 mW/cm2, the lowest in the table. From 1.34 to 30 MHz the limit is 180 divided by frequency squared, which at 14 MHz is 180 divided by 196, or about 0.92 mW/cm2. Below 30 MHz the limit gets looser as frequency drops, not tighter. So the same power density is more of a concern at 146 MHz.
Source: 47 CFR 1.1310, radiofrequency radiation exposure limits
-
You hold a General license in the United States and want to call CQ on upper sideband voice on 20 meters. Which of these frequencies is within your privileges?
- 14.160 MHz
- 14.200 MHz
- 14.240 MHz
- 14.100 MHz
Show answer
Answer: C. Under 47 CFR 97.301, General licensees in ITU Region 2 have 14.025 to 14.150 MHz and 14.225 to 14.350 MHz on 20 meters. Under 97.305, phone is allowed only from 14.150 to 14.350 MHz. That leaves General voice at 14.225 to 14.350 MHz, so 14.240 MHz fits, with the upper sideband staying inside the segment. 14.160 is Extra only, 14.200 needs Advanced or higher, and 14.100 is in the RTTY and data segment, not phone.
-
During a wildfire, phone and internet service in your area are down. A stranded hiker reaches you on a frequency outside your license privileges and reports that a person is badly hurt. What do FCC rules allow?
- You must stay silent and report the call once phone service returns
- You may reply, but only after a RACES official gives permission
- You may reply, but only by using Morse code on that frequency
- You may use any radio means available to you to handle the call
Show answer
Answer: D. Under 47 CFR 97.403, nothing in the amateur rules stops a station from using whatever radio means it has to meet urgent communication needs when human life or property is in immediate danger and normal systems are not available. A badly hurt person, with phone and internet service down, meets that test. No permission from RACES or anyone else is needed first, and no particular mode is required.
Source: 47 CFR 97.403, safety of life and protection of property
-
Around noon, every signal on 20 meters fades out within a few minutes, from all directions. A friend on the night side of the Earth reports normal conditions. Which is the most likely cause?
- A solar flare boosting D region absorption
- Tropospheric ducting setting up over your local area
- A sporadic E opening forming over your region
- Meteor scatter disturbing the F region overhead
Show answer
Answer: A. A sudden fade across HF on the daylit side of the Earth is the pattern of a solar flare radio blackout. The flare boosts the D region, which then absorbs HF signals passing through it. The night side gets no sunlight, so it is not affected. Ducting, sporadic E and meteor scatter are ways signals travel farther, not causes of a sudden daytime fade on every path.
-
You check the voltage across a 1 megohm resistor in a high-impedance circuit using a meter with 100 kilohms of input resistance. The reading is much lower than expected. What is the most likely reason?
- Voltmeters must be connected in series with the part being measured
- The resistor has gone open and no longer carries any current
- The meter is showing RMS instead of peak voltage on a DC circuit
- The meter draws current in parallel and loads the circuit
Show answer
Answer: D. A voltmeter connects in parallel and draws some current. Put 100 kilohms in parallel with 1 megohm and you get only about 91 kilohms, so the meter changes the circuit it is measuring. An open resistor would usually read higher, not lower. Use a meter whose input resistance is much higher than the circuit's, for example 10 megohms.
Source: OpenStax College Physics 2e, 21.4 DC voltmeters and ammeters
-
You connect an antenna analyzer, set for a 50 ohm system, right at the feed point of a new HF antenna. It shows an SWR of 3 to 1 and zero reactance. Which feed point resistances could give that reading?
- 150 ohms only
- 150 ohms or about 17 ohms
- 100 ohms or 25 ohms
- 150 ohms or 75 ohms
Show answer
Answer: B. For a purely resistive load, SWR is the larger of the load resistance and the line impedance divided by the smaller. 150 divided by 50 is 3, and 50 divided by about 16.7 is also 3, so both fit. As a check, the reflection coefficient is (150 minus 50) divided by (150 plus 50), or 0.5, and (16.7 minus 50) divided by (16.7 plus 50) is about minus 0.5. Either way, (1 plus 0.5) divided by (1 minus 0.5) gives 3 to 1. 100 or 25 ohms would read 2 to 1 and 75 ohms 1.5 to 1, so the SWR number alone cannot tell you whether the feed point is above or below 50 ohms. Read the analyzer's resistance value before you choose a matching method.
Source: Wikipedia: standing wave ratio
-
A session has three accredited VEs: two hold Amateur Extra licenses and one holds an Advanced license. The candidate is the niece of one of the Extra VEs and wants to take Element 4. What must happen?
- It can go ahead, because two of the three VEs hold Extra licenses
- It can go ahead, as long as her uncle does not grade her answers
- It can go ahead, because nieces are not on the rule's list of relatives
- It needs at least three Extra class VEs, none of them related to her
Show answer
Answer: D. Under 47 CFR 97.509, a team of at least 3 VEs must administer each exam, and every administering VE for an Amateur Extra exam must hold an Amateur Extra license. A VE may not administer an exam to a relative, and nieces are on the rule's list. This team fails on both counts, and keeping her uncle away from grading does not fix it.
-
An audio stage uses an ideal op amp in the inverting configuration with a 4.7 kilohm input resistor and a 47 kilohm feedback resistor. What is its voltage gain?
- +10
- +11
- -10
- -0.1
Show answer
Answer: C. The gain of an inverting amplifier is minus the feedback resistance divided by the input resistance: 47 divided by 4.7 is 10, so the gain is -10. The minus sign means the output is inverted. A gain of +11 is what the non-inverting configuration would give: 1 plus 47 divided by 4.7.
Source: Electronics Tutorials, inverting operational amplifier
-
Your repeater transmitter puts out 100 watts. The feed line loses 2 dB, the duplexer loses 1 dB, and the antenna has 9 dB of gain over a half-wave dipole. What is the effective radiated power?
- About 400 watts
- About 800 watts
- About 200 watts
- About 600 watts
Show answer
Answer: A. Under 47 CFR 97.3, ERP is the power supplied to the antenna times its gain over a half-wave dipole. The net change is 9 minus 2 minus 1, or +6 dB. Six dB is a power ratio of about 4 (10 to the power 0.6 is 3.98), so 100 W times 3.98 is about 400 W. 800 W ignores the losses, and 600 W treats decibels as a simple multiplier.
Source: 47 CFR 97.3, definitions (ERP)
What you get with VirtuePrep Ham Radio prep
- 915 practice questions built around the topics the Ham Radio tests.
- An explanation for every answer, so each mistake teaches you something.
- Stats and history that show your weakest topics first.
- Web, iPhone and Android, so you can study wherever you have ten minutes.
Ham Radio practice test questions people ask
How many questions are on the Extra ham radio test?
What is the ham radio technician passing score?
How hard is the ham radio test?
How much does a ham license cost?
How long should I study for the Technician exam?
Does this page cover the ham radio practice test for Canada?
Sources
- 47 CFR 97.501, qualifying for a license
- 47 CFR 97.503, element standards
- 47 CFR 97.505, element credit
- 47 CFR 97.509, administering VE requirements
- 47 CFR 97.5, station license required
- 47 CFR 97.21, license renewal
- 47 CFR 97.25, license term
- 47 CFR 1.1102, FCC application fees
- ARRL, question pools
- ARRL, withdrawn questions
- ARRL, new Technician pool released, effective July 1, 2026
- ARRL, getting licensed
- ARRL, what to bring to an exam session
VirtuePrep is not affiliated with or endorsed by the organisation that runs the Ham Radio. Exam names are trademarks of their owners. Practice questions are written for study and are not real exam questions. Page updated 2026-11-12.
Start your Ham Radio prep today
Answer your first question in under a minute. Free to try.