Automotive and CDL 617 practice questions

ASE A Series (A1 to A9) Practice Test

Practise for the ASE A Series (A1 to A9) with 617 exam-style questions, an explanation for every answer and stats that show what to study next.

Every answer explainedAn explanation for every answer as you practise.
Progress by topicSee which parts of the ASE A Series (A1 to A9) need more work.
Short or full setsTen-minute sessions or longer timed practice.

ASE A1 to A9 practice test and certification basics

The ASE A series is a set of nine separate certification tests for car and light truck technicians, set by the National Institute for Automotive Service Excellence (ASE). Each test, from A1 Engine Repair to A9 Light Vehicle Diesel Engines, is its own credential, and passing A1 to A8 with approved work experience earns ASE Master Automobile Technician status. A9 is not required for Master. The free ASE A1 to A9 practice test below has 20 new questions spread across all nine tests, each with an explanation for every answer.

ASE's tests cover technicians who diagnose and repair cars, SUVs and light-duty trucks up to Class 3. Initial A1 to A9 certification tests are taken in person at Prometric test centers. For these tests, only recertification can be taken online with remote proctoring.

Who can take the A series tests?

Anyone can register and sit a test, but a certificate needs two things: a pass and approved work experience. ASE puts A1 to A9 in its Repair Technician group, which asks for two years of full-time hands-on experience or the part-time equivalent.

ASE accepts some training in place of part of that time:

  • An ASE-accredited training program, completed: one year of credit.
  • An ASE-accredited manufacturer co-op program, completed, including its hands-on work portion: two years of credit.
  • Three or more different ASE Entry-Level Certification tests passed: one year of credit.
  • Other training: one month of credit for every two months of full-time training (or 200 program hours), up to one year.

You cannot combine these substitutions with each other, but you can add any one of them to hands-on work. You can also test before you have the experience. You get a score report, but ASE holds the certificate until your work experience form is approved.

How many questions are on each ASE test?

ASE's 2026 study guide gives these lengths. Each certification test adds 10 unscored research questions to the scored count. You cannot tell which ones they are, so answer every question.

Test Name Scored questions (total) Time Recert questions Recert time
A1 Engine Repair 45 (55) 75 min 23 30 min
A2 Automatic Transmission/Transaxle 45 (55) 75 min 23 30 min
A3 Manual Drive Train and Axles 40 (50) 60 min 20 30 min
A4 Suspension and Steering 40 (50) 60 min 20 30 min
A5 Brakes 45 (55) 75 min 23 30 min
A6 Electrical/Electronic Systems 50 (60) 90 min 25 45 min
A7 Heating and Air Conditioning 50 (60) 75 min 25 30 min
A8 Engine Performance 50 (60) 75 min 25 45 min
A9 Light Vehicle Diesel Engines 50 (60) 75 min 25 30 min

All questions are multiple choice. ASE's sample questions include several styles, among them the two-technician format where you decide whether Technician A, Technician B, both or neither is right. A1 to A9 offer a side-by-side Spanish and English option, and ASE provides a Spanish and English glossary.

What each A series test covers

Every test is split into content areas, each with a fixed number of scored questions. A weak spot in the heaviest area costs you the most.

Test Heaviest area (ASE 2026 weight) Next heaviest
A1 General engine diagnosis, 40% Fuel, electrical, ignition, air induction and exhaust, 20%
A2 Transmission/transaxle diagnosis, 58% In-vehicle maintenance and repair, 27%
A3 Four-wheel drive/all-wheel drive components, 20% Transmission, transaxle and drive axle, 17% each
A4 Steering systems and suspension systems, 30% each Wheel alignment, 28%
A5 Hydraulic, power assist and parking brakes, 43% Disc brakes, 24%
A6 Body electrical systems, 34% General electrical/electronic diagnosis, 26%
A7 HVAC and engine cooling service and diagnosis, 42% Operating systems and related controls, 38%
A8 Computerized engine controls, 26% General diagnosis, 24%
A9 Fuel system, 26% Air induction and exhaust, 24%

The weights say a lot about each test. A2 is mostly diagnosis: 26 of its 45 scored questions sit in one area, so reading scan data and pressure test results matters more than overhaul steps. A3 is the opposite. Its questions are spread almost evenly over six areas, and no single topic carries the test.

A9's air induction and exhaust area includes turbochargers, glow plugs and aftertreatment (DOC, SCR, DEF and DPF), and its fuel area covers high pressure common rail and hydraulic electronic unit injector (HEUI) systems. A7's task list names R-12, R-134a and R-1234yf identification. ASE's guide also says A7 certification does not meet the EPA's Section 609 refrigerant requirement. ASE's separate Refrigerant Recovery and Recycling Review and Quiz program does.

How to split your study time by the official weights

Use the scored question counts as your study budget. If you have 20 hours for A8, the 2026 weights suggest about 5 hours on computerized engine controls, 5 on general diagnosis, 4 on fuel, air induction and exhaust, and about 3 each on ignition and emissions. Then shift time toward whatever you do least at work.

A practical order for one test:

  1. Download ASE's free 2026 study guide and read the task list for your test. Mark each task as daily work, occasional or rarely seen.
  2. Spend most of your time on rarely seen tasks inside the heaviest areas. For A5, hydraulic, power assist and parking brakes are 43% of the test, so a gap in master cylinder or booster diagnosis costs more than one in drum brakes at 11%.
  3. Do timed practice. A6 gives you 90 minutes for 60 questions; A3 and A4 give 60 minutes for 50. Work out your per-question pace before test day.
  4. When you miss a question, find the task it tests in the task list and review that task, not only the answer.

If you are aiming for Master, each test is a separate credential, so you can take them one at a time. VirtuePrep has 617 ASE A Series practice questions in its app if you want more after these 20; they are written for practice and are not ASE questions.

What does ASE certification cost in 2026?

ASE's registration page lists a $34 registration fee per order and $62 for each A series certification test. The fee for the eight Master tests alone adds up to $496 (8 x $62), plus registration for each order you place. Recertification tests also cost $62 each, with test fees capped at $186 per order, so one recertification order tops out at $220 including registration.

ASE sells tests in four 2026 windows: January 10 to March 31, April 10 to June 30, July 10 to September 30 and October 10 to December 31. After you buy, you have 90 days to schedule and take the test. You cannot change an appointment within three days of it. If you fail, ASE asks you to wait 30 full days before buying the same test again.

Recertification and the ASE Renewal App

A certification lasts five years. To renew, you take the recertification test, which is about half the length of the original and can be taken from home. You can recertify even after a credential has lapsed, as long as you held it before.

The ASE Renewal App is an alternative for A1 to A9, at $52 a year. It sends one question per certification every 30 days. Each correct answer earns one credit, and eight credits extend that certification's expiry by one year. Credits do not carry over, and the app cannot earn you a new certification. To keep Master status, ASE's Need to Know guide says you must pass the recertification test in each of the eight areas as that credential expires.

Browse other exam pages on the VirtuePrep exams list.

20 free ASE A Series (A1 to A9) practice questions

Answer each one yourself, then open the answer. No account needed. These are study questions, not real exam questions.

  1. A V6 engine has a steady misfire at idle. In a cylinder power balance test, disabling cylinder 5 drops engine speed by only about 10 rpm, while disabling any other cylinder drops it by about 80 rpm. Swapping the cylinder 5 ignition coil and spark plug with those from cylinder 3 does not move the misfire, and cranking compression is even on all six cylinders. What should the technician check next?

    1. The cylinder 5 ignition coil
    2. The camshaft position sensor
    3. The cylinder 5 fuel injector circuit
    4. Cylinder leakage on all six cylinders
    Show answer

    Answer: C. The small rpm drop shows cylinder 5 is doing little work. The misfire stayed in cylinder 5 after the coil and plug were swapped, so ignition is ruled out, and even cranking compression points away from a mechanical fault. Fuel delivery to that one cylinder is the next thing to test, then an intake leak at that cylinder if the injector checks good. A cam sensor fault would not single out one cylinder, and a leakage test on every cylinder repeats ground the compression test already covered.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  2. An engine lacks power at highway speed. A vacuum gauge on the intake manifold reads a steady 19 inHg at idle. With the engine held at 2,500 rpm, the reading falls gradually to 9 inHg over about a minute. Which of these is the most likely cause?

    1. A restriction in the exhaust system
    2. A leaking intake manifold gasket
    3. A burned exhaust valve
    4. Ignition timing set too far advanced
    Show answer

    Answer: A. Normal idle vacuum that slowly sinks while the engine is held at a raised speed points to exhaust back pressure building up, from something like a plugged converter or a crushed pipe. An intake leak gives low vacuum at idle, a burned valve makes the needle drop regularly, and timing faults show up as abnormal idle vacuum rather than a slow decline.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  3. At a steady 60 mph, scan data shows the torque converter clutch commanded fully applied. Engine speed is 1,960 rpm and turbine speed varies between 1,760 and 1,820 rpm. The manufacturer allows under 50 rpm of slip at full apply, and the TCC solenoid and its circuit test good. Which of these is the most likely cause?

    1. An open in the TCC solenoid control circuit
    2. Worn TCC friction material or low apply pressure
    3. A faulty output shaft speed sensor
    4. The engine has not reached operating temperature
    Show answer

    Answer: B. The module is commanding full apply and the electrical side tests good, yet engine and turbine speeds are 140 to 200 rpm apart. So the clutch itself is not holding, because of worn lining or low apply pressure. An open circuit would stop the apply, an output speed sensor does not measure converter slip, and a cold engine would usually keep the TCC from being commanded on.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  4. On an electronically controlled automatic transmission, the valve body and solenoid assembly is replaced in the vehicle. The fluid level and type are correct and no codes are stored, but upshifts are now harsh. The new assembly came with a calibration identification number on its label. What should the technician do next?

    1. Replace the transmission control module and retest
    2. Drain and refill the fluid, then road test again
    3. Replace the new assembly with another one
    4. Enter the calibration ID and run a scan tool relearn
    Show answer

    Answer: D. The control module shapes each shift using data for the solenoids it controls and adaptive values it learned on the old parts. A new assembly needs its calibration ID entered and the adaptive values reset and relearned, following the manufacturer's procedure. ASE's A2 task list names updating valve body calibration numbers and running module relearns with a scan tool. The fluid is already correct, and replacing the module or the new assembly skips the step that was missed.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  5. A pickup has a part-time four-wheel-drive transfer case with no center differential. The owner says that in 4H on dry pavement, the front tires scrub and the truck hops during tight parking turns. In 2H it turns normally, and all four tires are the correct matching size and pressure. What is the most likely explanation?

    1. Normal for a part-time system on dry pavement
    2. The front CV joints are binding in tight turns
    3. The transfer case drive chain is stretched
    4. The front axle ratio does not match the rear
    Show answer

    Answer: A. A part-time transfer case locks the front and rear driveshafts together. In a turn the front wheels travel farther than the rears, and on a high-grip surface that difference winds up the driveline until a tire slips. That is why these systems are meant for loose or slippery surfaces. Binding CV joints or a mismatched axle ratio would also show up in other conditions, and a stretched chain causes noise or jumping, not this pattern.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  6. A rear-wheel-drive car with a clutch-type limited slip differential starts to shudder and chatter on tight turns right after a rear axle fluid change. It did not do this before the service. Which of these should the technician check first?

    1. Ring and pinion backlash and tooth contact
    2. Axle shaft end play and bearing condition
    3. The lubricant and friction modifier used
    4. Pinion bearing preload
    Show answer

    Answer: C. Clutch-type limited slip units depend on the right lubricant, and many need a friction modifier added or blended in. A chatter that starts straight after a fluid change most likely comes from the wrong fluid or a missing additive. Backlash, end play and preload are not changed by a drain and refill, so they are less likely here.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  7. During a dry-park check on a rack-and-pinion car, with the wheels on the ground and an assistant rocking the steering wheel, the technician feels free play at the inner tie rod socket inside the rack boot. The outer tie rod end and rack mounts are tight. What is the correct repair?

    1. Adjust the rack yoke and leave the tie rods as they are
    2. Replace the outer tie rod end only
    3. Replace the steering column intermediate shaft
    4. Replace the inner tie rod, then check and set toe
    Show answer

    Answer: D. Play found at the inner tie rod socket means that joint is worn, so the inner tie rod is replaced. Changing a tie rod moves toe, so an alignment check and toe adjustment follow. A yoke adjustment takes up rack-to-pinion clearance, not socket wear, and the outer end and column shaft were not where the play was found.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  8. After a four-wheel alignment, a car tracks straight and the total toe is within specification, but the steering wheel sits about 10 degrees to the left when driving straight. What is the correct way to center the steering wheel?

    1. Remove the steering wheel and reinstall it one spline to the right
    2. Lengthen one tie rod and shorten the other by the same amount
    3. Adjust rear camber until the wheel is centered
    4. Shorten both tie rods by the same amount
    Show answer

    Answer: B. Turning both tie rod adjusters in the same steering direction by equal amounts moves the front wheels relative to the steering wheel without changing total toe. Moving the wheel on its splines leaves the steering gear off center, which can upset systems that use a steering angle sensor. Shortening both changes total toe, and rear camber does not set the steering wheel position.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  9. A car with its original DOT 3 brake fluid, now several years old, develops a soft, sinking pedal near the bottom of a long mountain descent. After the brakes cool, the pedal feels normal again, and no leaks are found. Which of these best explains the problem?

    1. Moisture in the fluid has lowered its boiling point
    2. Air is entering past the master cylinder reservoir cap
    3. The pads have overheated and glazed
    4. The brake booster check valve is leaking
    Show answer

    Answer: A. Glycol-based fluid picks up water in service, and the federal brake fluid standard sets a much lower minimum boiling point for humidified (wet) fluid: 140 C for DOT 3, against 205 C when dry. On a long descent the fluid can boil, and vapor compresses, so the pedal goes soft until things cool. Glazed pads give a firm pedal with weak stopping, and a booster fault makes the pedal hard.

    Source: 49 CFR 571.116, FMVSS No. 116 Motor vehicle brake fluids (Cornell LII)

  10. After a steering rack replacement and alignment, the stability control warning lamp stays on, and the customer says the brakes briefly applied by themselves on a straight road. With the wheels pointing straight ahead and the vehicle parked, scan data shows a steering angle of 18 degrees left and a yaw rate of zero. What should the technician do?

    1. Replace the yaw rate sensor
    2. Bleed the ABS hydraulic unit with the scan tool
    3. Clear the codes and road test the vehicle
    4. Calibrate the steering angle sensor
    Show answer

    Answer: D. Stability control compares the driver's steering input with the measured yaw rate and brakes individual wheels when they disagree. With the wheels straight, the sensor should read close to zero, so an 18 degree reading makes a straight-ahead car look like it is turning, and the system may intervene. Calibrating the steering angle sensor to the manufacturer's procedure fixes the cause. The yaw rate reading is plausible for a parked car, the hydraulic unit was not shown to be faulty, and clearing codes leaves the sensor reading wrong.

    Source: 49 CFR 571.126, FMVSS No. 126 Electronic stability control systems (Cornell LII)

  11. A low beam headlamp is dim. With the lamp on and the engine off, battery voltage is 12.6 V. Voltage drop on the feed side, from the battery positive post to the lamp's power terminal, is 0.2 V. Voltage drop from the lamp's ground terminal to the battery negative post is 1.7 V. Which of these is the most likely cause?

    1. A weak battery
    2. An incorrect bulb with too high a wattage
    3. High resistance in the lamp's ground circuit
    4. An open in the headlamp feed circuit
    Show answer

    Answer: C. A good circuit loses only a few tenths of a volt on each side. Here the ground side drops 1.7 V, leaving about 10.7 V across the bulb, so the ground path has too much resistance, for example from a corroded ground point. The battery at 12.6 V is fully charged, an open feed would leave the lamp off, and the feed-side drop is normal.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  12. A car's battery goes flat after sitting for four days. The technician fits an ammeter in series at the negative battery cable, using a jumper so the circuit is never broken, locks the car, and reads 1.1 A right away. What should the technician do next?

    1. Pull fuses one at a time until the current drops
    2. Wait the stated module sleep time, then read again
    3. Disconnect the battery for 10 minutes to reset the modules
    4. Disconnect the alternator output wire and recheck
    Show answer

    Answer: B. Many modules stay awake for a time after the car is locked, so a high reading right away does not show a fault. Keep the circuit unbroken, wait the manufacturer's stated sleep time, and then measure. Pulling fuses now would chase normal wake-up current, and disconnecting the battery wakes the modules again and restarts the wait. ASE's A6 task list includes measuring and diagnosing key-off battery drain.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  13. The right rear door lock does not move from the key fob or the door switches, while the other three locks work. With the actuator plugged in and its connector back-probed, a meter shows about 12 V of one polarity on a lock command and the reverse polarity on an unlock command. Which of these is the most likely cause?

    1. The right rear actuator or its linkage
    2. A failed body control module output
    3. A blown door lock circuit fuse
    4. A key fob with a weak battery
    Show answer

    Answer: A. The actuator is getting the correct voltage, and the polarity reverses between lock and unlock, so the control side is working. The fault is in the actuator or the mechanical linkage. A blown fuse or failed module output would stop the voltage, and the other doors working rules out the fob.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  14. A car's under-hood label shows R-1234yf. The shop only has a recovery machine for R-134a, and a technician suggests fitting adapters to the hoses to connect it. What should the shop do?

    1. Fit the adapters and flush the machine afterward
    2. Use EPA-certified recovery equipment made for R-1234yf
    3. Fit the adapters for recovery only, not for charging
    4. Recover with the R-134a machine, then send the tank to a reclaimer
    Show answer

    Answer: B. EPA rules give each approved refrigerant its own unique fittings, including on recovery and recycling equipment, and say an adapter should not be used to convert a fitting. Technicians must also use EPA-certified refrigerant handling equipment. Recovering R-1234yf into an R-134a machine would mix refrigerants and contaminate the machine, whatever happens to the tank later.

    Source: US EPA, Regulatory requirements for MVAC system servicing

  15. In a car with dual-zone automatic climate control, the driver's side blows the selected temperature but the passenger side always blows hot. The scan tool shows the passenger blend door commanded to full cold, while the reported door position stays at full hot. Which of these is the most likely cause?

    1. A low refrigerant charge in the system
    2. A heater control valve stuck open
    3. A faulty in-car temperature sensor
    4. The passenger blend door actuator or door
    Show answer

    Answer: D. The module is asking for full cold and the door is not moving, so the problem is the actuator or the door it drives. A low charge or a stuck heater valve would affect both sides, and a faulty sensor would change the command, which here is already correct.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  16. A MAF-equipped engine shows long-term fuel trim of +19% on both banks at idle. At a steady 2,500 rpm the trims fall to +3%. Fuel pressure is within specification. Which of these is the most likely cause?

    1. A weak fuel pump
    2. Partly clogged fuel injectors
    3. An air leak in the intake after the MAF sensor
    4. A MAF sensor reading higher than actual airflow
    Show answer

    Answer: C. Air that enters after the MAF sensor is not measured, so the module adds fuel. At idle that air is a large share of the total, and as airflow rises its share shrinks, so the trims fall. A weak pump or restricted injectors cause the most trouble under load, and a MAF that reads high would push the trims negative.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  17. An engine with variable valve timing sets a code for the intake camshaft not reaching its target position. Scan data shows the intake cam phaser responding slowly to commands, most noticeably just after a cold start. The oil level is correct, but the oil in the engine is a heavier grade than the one printed on the filler cap. What should the technician do first?

    1. Replace the oil control solenoid, then retest
    2. Change to the specified oil grade, then retest
    3. Replace the intake cam phaser, then retest
    4. Replace the camshaft position sensor, then retest
    Show answer

    Answer: B. Cam phasers are moved by engine oil fed through an oil control valve, so oil grade, level and condition change how quickly they respond, and thick oil is slowest when cold. ASE's A8 general diagnosis tasks include driveability problems caused by oil of the wrong type. Correcting a known fault that fits the symptom comes before replacing parts; if the code returns, test the solenoid and phaser. A failed cam sensor usually sets a signal circuit code rather than slow phaser movement.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), A8 task list

  18. On a warm engine, the scan tool shows engine coolant temperature at -40 F (-40 C), and the cooling fans are running. The sensor is a typical negative temperature coefficient thermistor fed by a reference voltage through a pull-up resistor in the module. Which of these is the most likely cause?

    1. A thermostat stuck open
    2. The ECT signal circuit shorted to ground
    3. An open in the ECT sensor or its signal circuit
    4. Low coolant level
    Show answer

    Answer: C. With this circuit, an open makes the signal rise to near the reference voltage, which the module reads as extreme cold, often shown as -40. The module then runs the fans as a fail-safe. A short to ground would read very hot, and a stuck-open thermostat or low coolant would not produce a value that extreme.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  19. A technician replaces one injector on a common rail light diesel. The new injector has a calibration code printed on it. After start-up, the engine idles rough and knocks more than before the repair. Which of these is the most likely reason?

    1. The high-pressure line was torqued incorrectly
    2. The fuel system was not primed
    3. The glow plug for that cylinder has failed
    4. The new injector's code was not entered in the ECM
    Show answer

    Answer: D. Each common rail injector is matched to a calibration code that tells the module how that injector flows. If the old injector's data stays in the module, that cylinder is fueled wrongly, causing roughness and knock. The task list for this test includes entering injector calibration codes with a scan tool. Air in the system usually causes hard starting, and a glow plug fault mainly affects cold starts.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

  20. A light diesel pickup used almost only for short town trips sets a high soot load message. The DPF differential pressure reading is high, and data shows several active regenerations that started but did not finish. Which of these is the most likely cause?

    1. Short trips that stop active regenerations
    2. A DEF concentration that is too low
    3. An overfilled diesel exhaust fluid tank
    4. A stuck-closed SCR dosing valve
    Show answer

    Answer: A. An active regeneration raises exhaust temperature to burn soot from the filter and needs enough steady driving time to finish. Repeated short trips keep stopping it early, so soot builds and pressure across the filter rises. DEF and SCR dosing affect NOx reduction, not the soot load in the DPF.

    Source: ASE Official Study Guide, Automobile Tests A1 to A9 (2026), task lists

Practise all 617 questions

What you get with VirtuePrep ASE A Series (A1 to A9) prep

  • 617 practice questions built around the topics the ASE A Series (A1 to A9) tests.
  • An explanation for every answer, so each mistake teaches you something.
  • Stats and history that show your weakest topics first.
  • Web, iPhone and Android, so you can study wherever you have ten minutes.

ASE A Series (A1 to A9) practice test questions people ask

How long does ASE certification last?
Each ASE certification is valid for five years. To keep it, you pass the shorter recertification test for that area, which you can take online with remote proctoring, or extend an A1 to A9 credential through the ASE Renewal App. If you recertify early, the time left on your old credential is not added on; a new five-year period starts from the recertification date.
What is the ASE passing score?
ASE does not publish a passing score or a number of correct answers for the A1 to A9 tests on its test pages, FAQs or 2026 study guide. Figures on prep sites disagree and do not cite ASE, so treat them with caution. Your score report from ASE shows how you did.
Which ASE test is the hardest?
ASE does not rank its tests by difficulty. What ASE does publish is length. A6 Electrical/Electronic Systems is the only A series certification test with 90 minutes, and A6, A7, A8 and A9 have the most scored questions at 50 each. How hard a test feels depends mostly on how much of that area you work on day to day.
Is the ASE certification test hard?
The tests are written for working technicians. ASE links every question to a task in its official task list, and many of those tasks ask you to diagnose a fault and decide what action is needed. Each certification test also holds 10 unscored research questions you cannot pick out, so answer everything. ASE's test pages and FAQs do not publish pass rates.
How do you become ASE certified?
Pass the test for an area and have your work experience approved. For A1 to A9, ASE's Repair Technician requirement is two years of full-time hands-on work or the part-time equivalent, and some training can count toward it. You can take the test first; ASE holds the certificate until your experience is approved.
How much does ASE certification cost?
At 2026 prices, ASE charges a $34 registration fee per order plus $62 for each A series test. Recertification tests are also $62 each, capped at $186 in one order, so the most one recertification order costs is $220. Check ASE's registration page before you buy, since fees can change.

Sources

  • ASE, Automobile and Light Truck Tests A1 to A9: https://www.ase.com/tests/a1-a9/
  • ASE, Official ASE Study Guide, Automobile Tests, 2026: https://ase.com/wp-content/uploads/ASE_Automobile_Study_Guide.pdf
  • ASE, How to register, test fees and windows: https://ase.com/tests/register-now/
  • ASE, FAQs: https://ase.com/faqs/
  • ASE, Certification: Need to Know (revised January 2026): https://ase.com/wp-content/uploads/ASE_CertificationNeedtoKnow.pdf
  • ASE, work experience form instructions: https://workexp.ase.com/FormInstr.aspx
  • ASE, test series list: https://www.ase.com/test-series

VirtuePrep is not affiliated with or endorsed by the organisation that runs the ASE A Series (A1 to A9). Exam names are trademarks of their owners. Practice questions are written for study and are not real exam questions. Page updated 2026-11-12.

Start your ASE A Series (A1 to A9) prep today

Answer your first question in under a minute. Free to try.

Start practising